Відео

Thank you - this was so informative and helpful. I inherited a 1987 Speedmaster from my brother-in-law and it hadn't been fired or cleaned since the 80's. Your step by step video was super clear and helped me get it apart for cleaning (and back together afterwards). Can't wait to see how it fires. Cheers!

That threaded plug is called a set screw .

How do you fix your cold ac.i have only heat coming out and my rear controls where the rear passengers can control went out just went dead

Help, been trying to install the bolt hold open and ai can get all the pieces reinstalled but still won’t hold open the bolt. Using the Volquartsen black bolt release. Any idea what I am doing wrong. ?

Good video, now my 10-22 is back working!!!!

,,, grippy side to brass ,

how much the thread and pitch size in barrel I've been looking for this for a long time, can AR15 barrel be installed on a Savage receiver?

Hit the bluetooth MS30 with the blow torch and it worked then dropped...Hit it again with more heat and it seems to have fixed it. At least I know root cause if it blows during the pork loin today :) Thanks for the advice !!!

I'm about to replace my friends rear shocks in her 03 tahoe. Your video helped give me even more confidence than I already had! Thank you

Ok Brother, I am sure we will both agree this is a JOKE of a fix. I made a video of the nationalmatchshim on my channel and yes it is going to cost you a grand total of $11 bucks, but it will remove every bit of that upper and lower slop PERMANENTLY my friend. Check it out and then let me know what you think. I have it on all my ARs and they are QUIET, none of that rattle you are dealing with

This worked on my pit boss electric! Thanks! Used a heat gun on the base of the heating element until smoking/steaming. I think there was moisture.

Very interesting. Nice work sir

You are wrong, there is no boot on my 2002 Tahoe.

That was pretty awesome. This really helped out my issue in my house

Enco were made in Europe but that factory is closed. This is very similar to my Shenwai900 12 X 36 Taiwanese lathe except mine has a screwed on chuck. I had to make a special tool to change the chucks. I have it 40 years and would not take any money for it because it is so good. The solenoid forward and reverse switch is long burned out but I fitted a push pull cable to it instead and it works perfectly. The slides as scraped on mine too.

Toll gemacht und wunderschön, aber so viel Arbeit???

It might not work for everyone, but it worked for me. Thanks!

Try a multitool.

I tried starting out with a mini lathe and then I got in the car accident and my girlfriend kept everything and sold everything when I was in the hospital. It sucks when you come home to no tools

Thank You!! I'm in the process of restoring a MW 1943 model. I'm to the head stock cleaning. This video helped me.

Do you know how to make mossberg 590 magazine tube to frame threads

You shouldve just taken of the treads, placed your new uncut stringer against the side of one of the exisiting stringers and just traced it. Then you have the oppertunity to replace the nails in the stair treads with screws. 3 -4 hour job

I made a square cutting tool seven years ago for a magazine tube I had to thread at 1:12 tpi, but I don't recall putting any angle on the cutting tip. The tube has fairly loose tolerances, so maybe that's why I got away with it. I am about to modify another tube, so I watched your videos as a refresher. My only wish is that you had shown all the math needed to determine the angle in degrees. After a couple of hours of research I finally figured it out and realized you rounded up to the nearest whole number.

Great video. I recently bought the same lathe. What oil do you use in the head stock is it iso32. Thanks

I just did the electronic front and electronic/air rear shocks on my 2003 Yukon Denali. I used a jack and jack stands. With the Yukon on stands, the jack was used to support the axle and the control arms. I removed the wheels and the rear fender liners for better access in the back. For the fronts, the liner could be pushed out of the way. I used a pair of vise grips on the front shocks to keep them from spinning while removing the top 15mm nut. The jack was also very useful for compressing the front shocks so there were enough threads exposed to push the electronic connector on until it clicked into place. For anyone doing this job, the grey plastic portion of the front shock electronic connector rotates to release it from the shock. That was the only tricky part to figure out. Total time was about 2 hours. A shop quoted me $640 to do the job.

Great help!!!!!!!

Looks good. The only comment I have is to have longer bolts so you could add locking nuts. Thanks for the video

So helpful! Many thanks!!!

Good ❤❤❤❤❤❤

I believe the action is Rem model 30.S. Caliber could very well be a 375 H & H.

Great video! Excellent work. Very simple. How did it shoot?

Great to see a stock made by a person with "normal" tools! No belt sander, etc. What finish did you use on the stock?

How can I tell how old my 552 is

Roll up a piece of tape for the back side to hold it while you sand it

Thanks for making this video. Just picked one up from a pawn shop.

Never seen a barrel where the OD ran true with the bore. Your thread relief groove is way to wide, A 5/8-24 thread should be 5/8 long, not 1/2. then you would not need to shorten your thread protector. My 2 cents.

So, what ever happened with the action?

Nice job bringing an old gun back to life! I've had some luck using a clear cyanoacrylate and mixing it with the sanding dust from the wood. It still won't be a perfect match to the original but it's pretty close. The sanding dust doesn't seem to interfere with the accelerant.

What kind of chuck are you using to hold the barrel?

looks like a great machine, how much did you pay?

How about heat melting the tape ?

I LOVE THAT RATCHET!!!!

The ways are gorgeous on that!!!! I have a 5914 and love it. Its the lathe I learned on in HS.

What if a guy has some minor scratches in the clear or even small chips in the clear but the wood is ok. Can I do anything to remedy the eyesore? On a rem 700 bdl with the gloss finish

I have a SB 11”. Wondering what does the L refer to also a Heavy 10. Thanks

Wouldn't it have been better to cut the threads at the correct length, instead of cutting the thread protector? Most threads are long enough to put a lock nut and some even come with a spacer washer. Now it's so short that only has option for one style device. Even my 10mm pistol comes with longer thread's.

Where did you get the grey body to apply to the end of the barrel? Part # and or fitting.

May i ask what quick change tool post are you using ? and did you need to modify anything to put it on ?

Camfor?

This is helpful. I have a heavy 10 L and I can’t remove the handle. Taper pin is out. Back gear is still installed. All I want to do is clean it. So I’ll try tapping from the front. Thanks.